2.9.6. Removal of an intermediate asterisk and shaft


Section of a damper of fluctuations of a bent shaft and pulley

1 — a pulley
2 — bolts
3 — washers
4 — a damper of fluctuations
5 — pins
6 — a flange
7 — oil consolidation

8 — a flange
9 — an asterisk of a bent shaft
10 — a segment spline
11 — a bent shaft
12 — an adjusting pin
13 — the cap-type spring
14 — a bolt

If the engine is not removed from the car yet, at first execute the following operations:

 PERFORMANCE ORDER

  1. Remove a radiator.
  2. Remove the air cleaner.
  3. Remove a natyazhitel of a distributive chain.
  4. Remove the distributor.
  5. Remove the inlet pipeline on the engine of model M 110.
  6. Take off a driving belt of the water pump / generator.

Engine M 123

 PERFORMANCE ORDER

  1. Bring the piston of the 1st cylinder in the provision of VMT.
  1. Turn off a bolt and remove a casing of a guide of the distributor and a pro-rate.
  1. Notice the provision of a groove in driving to a shaft, then take out a shaft from the block of cylinders by means of passatizhy with a long sock.
  2. Remove where is available, a hydraulic pump of a control system of height of a back suspension bracket.
  3. By means of an internal six-sided face key turn off cover bolts from a forward part of the block of cylinders and remove laying.
  4. Turn out a bolt from a camshaft asterisk, holding it in motionless situation by means of the metal bar passed in one of openings.
  5. Shift an asterisk, remove it from a chain and tie to one party.
  6. By means of an internal six-sided face key turn off bolts of a pulley and a damper of fluctuations from a forward flange of a bent shaft.
  7. By means of the hammer or a stripper remove the lower axis of the right guide of a chain through an opening in a flange and take a guide up. If there is no opening, remove a flange.
  1. Turn out a bolt from an intermediate asterisk, keeping it from a provorachivaniye by means of the metal bar passed through an opening in an asterisk.
  1. Turn out a restrictive bolt of a chain on the left side of the block of cylinders.

    Removal of a restrictive hairpin of a distributive chain

  1. Push out an intermediate shaft back and take out an asterisk.
  2. Turn off the fixing bolt of the bearing and remove a washer.
  1. By means of a suitable bolt extend an intermediate shaft together with the forward bearing.
  1. Remove the bearing from a shaft.


Engine M 110

Removal of an intermediate gear wheel (engine M 110)


 PERFORMANCE ORDER

  1. Take an inertial stripper a cap on the left side of the block of cylinders.
  2. Take a shaft of the drive of the oil pump by means of a stripper bolt.
  3. Turn off an internal six-sided face key bolts of a pulley and a damper of fluctuations from a forward flange of a bent shaft.
  4. Turn off the top stopper from a VMT sensor arm, then turn out and remove the reducing valve of pressure of oil.
  5. Turn off bolts of the case of the distributor and remove laying. Remove a lead.
  6. Holding an intermediate gear wheel from a provorachivaniye, turn out a bolt of a supply of oil and remove a washer.
  7. Turn off a restrictive hairpin of a chain on the left side of the block of cylinders.
  8. Tapping on the intermediate hall, shift it back and remove up.
  9. Close pure cleaning material the lower part of the drive of the camshaft.
  10. Turn off the fixing bolt of the bearing and remove a spring lock ring and a washer.
  11. By means of a suitable bolt take an intermediate shaft together with the forward bearing. Remove the bearing from a shaft.
  12. If it is necessary, take out a stripper the back bearing from the block of cylinders.